| 
| (1) FM30B
Six different display modes in the panel for
setup, VU levels, and frequency operation
SMT design used throughout for maximum reliability
0-40mW continuously variable output power
PLL synthesized for drift free operation
Front panel digital control and display of all settings and parameters
Professional metal case for noise-free operation
EMI filtering on audio and power inputs
Super audio quality, rivals commercial broadcasts
Factory assembled and tested to guaranteed specifications
Includes line level monitor outputs, improved stereo separation and audio clarity! 110-240VAC power adapter included.
We took the exceptional circuitry of the FM25 and built a stand-alone "radio station" around it, complete with microphone and line level audio mixers, digital control and display of operating frequency, higher RF power output options, and put it all in a professional case. To date, the FM30B continues to be our #1 selling transmitter! There are two
reasons why.... reliability and unmatched product support.
INCREASED PERFORMANCE WITHOUT THE FRILLS
The FM30B is designed around an RF tight vinyl clad metal enclosure for noise free and interference free operation. All settings are done without taking the cover off! Enter the setup mode from the front panel and step through the menu to make all of your adjustments. A two line LCD display shows you all the settings! In addition to the LCD display, a front panel LED
indicates the PLL lock so you know you are transmitting. Besides frequency selection, the front panel control and display gives you 256 steps of audio volume (left and right combined) as well as RF output power. A separate balance setting compensates for left/right differences in audio level. In addition to settings, the LCD display shows you "Quality of Signal" to help you set your levels for optimum sound quality. And of course, all settings are stored in the non-volatile memory
for future use! The design includes EMI filters on line level audio and power inputs, and a state of the art microstrip PCB inductor for the ultimate in alignment-free operation. RF output is through a professional, well-shielded rear panel BNC connector for a perfect antenna match. Standard RCA connectors are used for left and right line level audio inputs. Power input is 13.8 to 16VDC and includes a 15VDC plug in power supply. The stylish metal case measures 5.55"W x
6.45"D x 1.5"H.
FM30B- BROADCAST PERFORMANCE. RF output power is a conservative and cool running 40mW, and is front panel variable throughout the entire range of 0-40mW continuous duty. Audio pre-emphasis is available for either North American or European standard. This product is fully assembled, tested, and ready to go! Unit has a sharp looking metal cabinet, external whip antenna and 110-240 VAC power supply. Full one-year parts and labor warranty.
(2) The TM100 Antenna is our Number One selling product. Matching your antenna to your transmitter is the single most important link in your transmitter set-up - and a good antenna and match is the secret to getting maximum range. When we say match we mean electrical impedance match... if the proper impedances are not maintained between transmitter and antenna, power is reflected back away from the antenna and back into the transmitter! This can cause the final amplifier stage
to be damaged, not to mention a spurious signal and lousy range. Our antenna consists of rugged pre-cut PVC pipe, antenna radiating elements and of course the proper matching assembly and is fully water-resistant when assembled. The antenna is easily mounted to any standard TV antenna mast like you can find at Radio Shack or K-Mart. A standard ‘F’ style coax connector is used (included), so that readily available, low cost RG-59 TV coaxial cable can be used for
connection. And we even supply the F Male adapter for easy connection to any transmitter antenna jack. Total length of the antenna is about five feet, and it is easily mounted horizontally or vertically polarized - yes, we even explain in the manual the pluses and minuses for each. Maximum input power is now 25 watts. This antenna version comes fully soldered and mostly assembled with all of the electronics components soldered and ready to go. Some assembly of the PVC and mounting parts
is required (about 15 minutes assembly time). You will want to mount the antenna to check fitting and test directional positioning before finalizing the assembly. The PVC covering can be glued for weatherproof sealing once you are satisfied with the mounting. |
